Application of artificial neural network method to predict the breakage properties of PGE bearing chromite ore

In the present investigation, systematic grinding experiments were conducted in a laboratory ball mill to determine the breakage properties of low-grade PGE bearing chromite ore. The population balance modeling technique was used to study the breakage parameters such as primary breakage distribution (B_{i, j}) and the specific rates of breakage (S_i). The breakage and selection function values were determined for six feed sizes. The results stated that the breakage follows the first-order grinding kinetics for all the feed sizes. It was observed that the coarser feed sizes exhibit higher selection function values than the finer feed size. Further, an artificial neural network was used to predict breakage characteristics of low-grade PGE bearing chromite ore. The predicted results obtained from the neural network modeling were close to the experimental results with a correlation of determination R² = 0.99 for both product size and selection function.     

Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

Adenine-functionalized conjugated polymer as an efficient photocatalyst for hydrogen evolution from water

Conjugated polymers have emerged as a promising class of organic photocatalysts for photocatalytic hydrogen evolution from water splitting due to their adjustable chemical structures and electronic properties. However, developing highly efficient organic polymer photocatalysts with high photocatalytic activity for hydrogen evolution remains a significant challenge. Herein, we present an efficient approach to enhance the photocatalytic performance of linear conjugated polymers by modifying the surface chemistry via introducing a hydrophilic adenine group into the side chain. The adenine unit with five nitrogen atoms could enhance the interaction between the surface of polymer photocatalyst and water molecules through the formation of hydrogen bonding, which improves the hydrophilicity and dispersity of the resulting polymer photocatalyst in the photocatalytic reaction solution. In addition, the strong electron-donating ability of adenine group with plentiful nitrogen atoms could promote the separation of light-induced electrons and holes. As a result, the adenine-functionalized conjugated polymer PF6A-DBTO2 shows a high photocatalytic activity with a hydrogen evolution rate (HER) of 25.21 mmol g^?1 h^?1 under UV-Vis light irradiation, which is much higher than that of its counterpart polymer PF6-DBTO2 without the adenine group (6.53 mmol g^?1 h^?1). More importantly, PF6A-DBTO2 without addition of a Pt co-catalyst also exhibits an impressive HER of 21.93 mmol g^?1 h^?1 under visible light (λ > 420 nm). This work highlights that it is an efficient strategy to improve the photocatalytic activity of conjugated polymer photocatalysts by the modification of surface chemistry.     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

基于MF-DCCA 的呼吸道疾病与大气污染物相关性分析

针对呼吸道系统疾病与大气 PM2:5、 SO2 浓度序列的相关性特征, 应用多重分形消除趋势波动分析法 (MF-DCCA), 对张家界市永定区呼吸道系统疾病患病人数与大气 PM2:5、 SO2 浓度序列进行了研究。结果发现该地区 呼吸道系统疾病患病人数与大气 PM2:5、 SO2 浓度的相关性具有长期持续特征和多重分形特征。随后对它们相关性 多重分形特征的动力来源进行了分析, 通过随机重排和相位随机处理, 结果表明在不同时间尺度上的长期持续性影响 是其主要动力来源。进一步研究发现该地区呼吸道系统疾病与大气 PM2:5、 SO2 浓度序列的相关性在四个季节均具 有长期持续性的多重分形特征, 且夏季多重分形特征相对强于其他季节。     

Experimental research on micro hole drilling of polycrystalline Nd:YAG

Polycrystalline Nd:YAG materials have wide applications in solid-state lasers. In this study, micro hole drilling experiments were performed on polycrystalline Nd:YAG using a polycrystalline diamond micro drill. The hole diameter, edge chipping, and hole wall surface quality were examined in detail. The results showed that the hole diameter was slightly larger than tool diameter. A diameter error of less than 5.5% was achieved. The edge chipping at the entry hole was formed by the encircled petal shape exfoliations, which were produced by the indentation and rotation movement in the drilling entry stage. Edge chipping at the exit hole was generated by an entire piece of exfoliation, which was produced by a circle of microcracks around the tool tip propagating to the bottom surface in the drilling exit stage. The edge chipping width at the entry hole was smaller than that at the exit hole. Based on different material removal modes, the hole surface morphology was classified into three types: ductile removal, coexisting ductile and brittle removal, and brittle removal. The hole surface quality mainly depended on the proportion of the brittle fracture to ductile removal surface.     

Role of Polyinosinic:Polycytidylic Acid-Induced Maternal Immune Activation and Subsequent Immune Challenge in the Behaviour and Microglial Cell Trajectory in Adult Offspring: A Study of the Neurodevelopmental Model of Schizophrenia

Multiple lines of evidence support the pathogenic role of maternal immune activation (MIA) in the occurrence of the schizophrenia-like disturbances in offspring. While in the brain the homeostatic role of neuron-microglia protein systems is well documented, the participation of the CX3CL1-CX3CR1 and CD200-CD200R dyads in the adverse impact of MIA often goes under-recognized. Therefore, in the present study, we examined the effect of MIA induced by polyinosinic:polycytidylic acid (Poly I:C) on the CX3CL1-CX3CR1 and CD200-CD200R axes, microglial trajectory (MhcII, Cd40, iNos, Il-1β, Tnf-α, Il-6, Arg1, Igf-1, Tgf-β and Il-4), and schizophrenia-like behaviour in adult male offspring of Sprague-Dawley rats. Additionally, according to the “two-hit” hypothesis of schizophrenia, we evaluated the influence of acute challenge with Poly I:C in adult prenatally MIA-exposed animals on the above parameters. In the present study, MIA evoked by Poly I:C injection in the late period of gestation led to the appearance of schizophrenia-like disturbances in adult offspring. Our results revealed the deficits manifested as a diminished number of aggressive interactions, presence of depressive-like episodes, and increase of exploratory activity, as well as a dichotomy in the sensorimotor gating in the prepulse inhibition (PPI) test expressed as two behavioural phenotypes (MIA_PPI-low and MIA_PPI-high). Furthermore, in the offspring rats subjected to a prenatal challenge (i.e., MIA) we noticed the lack of modulation of behavioural changes after the additional acute immune stimulus (Poly I:C) in adulthood. The important finding reported in this article is that MIA affects the expression and levels of the neuron-microglia proteins in the frontal cortex and hippocampus of adult offspring. We found that the changes in the CX3CL1-CX3CR1 axis could affect microglial trajectory, including decreased hippocampal mRNA level of MhcII and elevated cortical expression of Igf-1 in the MIA_PPI-high animals and/or could cause the up-regulation of an inflammatory response (Il-6, Tnf-α, iNos) after the “second hit” in both examined brain regions and, at least in part, might differentiate behavioural disturbances in adult offspring. Consequently, the future effort to identify the biological background of these interactions in the Poly I:C-induced MIA model in Sprague-Dawley rats is desirable to unequivocally clarify this issue.     

Stumped nature hyperjerk system with fractional order and exponential nonlinearity: Analog simulation,bifurcation analysis and cryptographic applications

This article presents the construction and consumption of hyperjerk system having chaotic nature with the commensurate ordered fractional derivative on rapidly digitalized emerging technologies. The system analyzed analytically using Lipschitz condition and numerically with the help of predictor corrector approaches. Originality of constructed system is confirmed using log error plots which gives satisfactory small values on finite time scale. The dynamical performances of the complex system are termed in multiple phase planes by the mean of their significant nature. Stability and bifurcation analysis around the fractional derivative is also studies for the various parameter of system to check the visibility of chaotic solution. The system is also designed in analog circuit simulator with the aid of operational amplifier, anti-parallel semiconductor diodes for validation of the system. With the help of random number generators (RNGs), binary array generated from the hyperjerk system and plugged in to the NIST 800–22 test suite to measure the randomness. The array having high randomness is used as strong cypher key for the cryptographic execution straightforwardly in both direction encryption and decryption.     

Coastal trapped waves in the southern Caspian Sea

Previous studies reported coastal trapped waves (CTWs) in the Caspian Sea (CS). This study deals with the generation mechanisms, the temporal and spatial variability of CTWs in this area, and their transformations during propagation from the origin to the destination using recent measurements and high-resolution numerical simulations. CTWs are observed at all stations with periods of 2–6 days after northerly storms. The Absheron Peninsula, old Sefidrud delta, and Nur coasts were identified as the CTWs prone regions. The generation of CTWs in these locations was confirmed using numerical experiments. The propagation away from the generating location of CTWs was analyzed using a representative real wind storm. In the west part of the CS, the generation mechanism of CTWs is mainly similar to the barotropic Kelvin waves; in contrast, it is similar to the continental shelf waves in the southern shelves. The results can be used to study the contribution of generated CTWs to the transport of sediment and biological materials in all large lakes.     

Comparative study of LuxY1-xAG (x=0..1) laser ceramics doped with 5% Yb3+

Materials with high thermo mechanical properties are required as laser media for high-powered lasers. One of such materials is lutetium-aluminum garnet (LuAG) doped with ytterbium. In the present work, we discuss for the first time a full comparative study of 5% Yb-doped LuYAG ceramics with variation Lu/Y ratio. Samples were prepared with addition of B₂O₃, MgO and SiO₂ which were used as sintering aids. Grain sizes, shrinkage curves, lattice constants and transmission spectra were measured for all samples. Thermal conductivity was measured in a wide temperature range for all studied samples. Output power of 12 W and 60% slope efficiency were obtained on the 5% Yb:LuAG disk laser.